NXOS¶
This section lists down all those services which are only specific to NXOS. For list of all the other service please refer this: Common Services.
Important
In argument table
values in parenthesis are default values.
mandatory arguments are marked with
*.
shellexec¶
Service to execute commands on the Bourne-Again SHell (Bash).
Argument |
Type |
Description |
|---|---|---|
timeout |
int (default 60 sec) |
timeout in sec for executing command on shell. |
reply |
Dialog |
additional dialog |
command |
list |
List of command to execute on shell |
target |
standby/active |
by default commands will be executed on active, use target=standby to execute command on standby. |
rtr.shellexec(['uname -a'])
cmd = ['uname -a', 'ls -l']
rtr.shellexec(cmd)
If you want to run bash commands as root in the Linux shell, you can add sudo su root
to the command list. Please note that you need to add ‘exit’ explicitly to the command
list to return to the user bash shell. (The shellexec service will automatically
execute another ‘exit’ command to return to the NXOS command prompt.)
cmd = ['sudo su root', 'uname -a', 'whoami', 'exit']
rtr.shellexec(cmd)
Note: if the sudo prompt asks for a password, you need to pass the reply Dialog object
to respond to the password prompt. Credentials are available in rtr.credentials.
from unicon.eal.dialogs import Dialog
from unicon.plugins.generic.statements import GenericStatements
statements = GenericStatements()
password_stmt = statements.password_stmt
cmd = ['sudo su root', 'uname -a', 'whoami', 'exit']
device.shellexec(cmd, reply=Dialog([password_stmt]))
configure¶
Service to execute commands on configuration mode.
Argument |
Type |
Description |
|---|---|---|
command |
list |
list of commands to configure |
reply |
Dialog |
additional dialog |
timeout |
int |
timeout value for the command execution takes. |
error_pattern |
list |
List of regex strings to check output for errors. |
prompt_recovery |
bool (default False) |
Enable/Disable prompt recovery feature |
target |
str (default “active”) |
Target RP where to execute service, for DualRp only |
mode |
str (default: “default”) |
Mode to configure (“default” or “dual”) |
rtr.configure(['feature isis', 'commit'], mode="dual")
# config dual-stage
# Enter configuration commands, one per line. End with CNTL/Z.
# R1(config-dual-stage)# feature isis
# R1(config-dual-stage)# commit
# Verification Succeeded.
# Proceeding to apply configuration. This might take a while depending on amount of configuration in buffer.
# Please avoid other configuration changes during this time.
# Configuration committed by user 'admin' using Commit ID : 1000000002
# R1(config-dual-stage)# end
# R1#
If you want to bring device to configure dual stage, you can use the go_to function in state machine
and use 'config_dual': True as the context. The following is an example to do that.
rtr.state_machine.go_to('config', rtr.spawn, context={'config_dual': True})
# config dual-stage
# Enter configuration commands, one per line. End with CNTL/Z.
# R1(config-dual-stage)#
# execute command in configure dual stage
rtr.execute('no logging console')
# R1(config-dual-stage)# no logging console
# R1(config-dual-stage)#
attach¶
Service to attach to line card to execute commands in. Returns a router-like object to execute commands on using python context managers.
Argument |
Type |
Description |
|---|---|---|
module_num |
int |
module number to attach to |
timeout |
int (default 60 sec) |
timeout in sec for executing commands |
target |
standby/active |
by default commands will be executed on active, use target=standby to execute command on standby. |
with device.attach(1) as lc_1:
output1 = lc_1.execute('show interface')
attach_console¶
Service to attach to line card console to execute commands in. Returns a router-like object to execute commands on using python context managers.
Argument |
Type |
Description |
|---|---|---|
module_num |
int |
module number to attach console to |
login_name |
str |
name to login with, default: root |
default_escape_chars |
str |
default escape char, default: ~, |
change_prompt |
str |
new prompt to change to for ez automation |
timeout |
int (default 60 sec) |
timeout in sec for executing commands |
prompt |
str |
bash prompt (default: bash-d.d# ) |
with device.attach_console(1) as lc_1:
output1 = lc_1.execute('ls')
output2 = lc_1.execute('pwd')
ping6¶
Service to issue ping6 response request to another network from device.
Argument |
Description |
|---|---|
addr |
Destination address |
proto |
protocol(ip/ipv6) |
count |
Number of pings to transmit |
source |
Source address or interface |
data_pat |
data pattern that would be used to perform ping. |
dest_end |
ending network 127 address |
dest_start |
beginning network 127 address |
df_bit |
(y/n) y sets the DF bit in the IP header. |
dscp |
field DSCP in the IPv6 header. |
vrf |
vrf interface name |
mask |
Number of bits in the network mask of the target address. |
exp |
Experimental (EXP) bits bits in MPLS header |
pad |
Pad pattern for MPLS echo request |
transport |
destination type as an MPLS traffic engineering (TE) tunnel |
oif |
output interface |
reply_mode |
reply mode for the echo request packet |
size |
ping packet size to transmit |
ttl |
time-to-live (TTL) value |
tunnel |
Tunnel interface number |
tos |
TOS field value |
multicast |
multicast addr |
udp |
(y/n) enable/disable UDP transmission for ipv6. |
interface |
Interface |
vcid |
VC Identifier |
topo |
topology nam |
verbose |
(y/n) enable/disable verbose mode |
extended_verbose |
Enables extended verbose mode |
src_route_type |
source type strict/loose |
src_route_addr |
source route ip |
validate_reply_data |
(y/n) validate reply data or not |
force_exp_null_label |
(y/n) Force explicit null label. |
lsp_ping_trace_rev |
LSP ping/trace revision |
precedence |
precedence in the IPv6 header |
novell_type |
(y/n) To use the Novell Standard Echo type instead of the Cisco ping echo type. |
sweep_ping |
sweep ping command |
sweep_interval |
sweep interval |
sweep_min |
min packet size |
sweep_max |
max packet size |
extd_ping |
(y/n) enable/disable extended ping. |
ipv6_ext_headers |
(y/n) include extension header or not |
ipv6_hbh_headers |
(y/n) include hop by hop option or not. |
ipv6_dst_headers |
(y/n) include destination option or not. |
timestamp_count |
number of timestamps |
record_hops |
Number of hops |
- return :
ping command response on Success
raise SubCommandFailure on failure.
#Example
--------
output = ping6(addr="2001:cdba:0:0:0:0:3257:9652")
output = ping6(addr="2001:cdba:0:0:0:0:3257:9652", extd_ping='yes')
list_vdc¶
As the name suggests, it returns the names of all the VDCs in the list format.
Please note that unlike most of the services, the return here is not of type
str but list.
Argument |
Type |
Description |
|---|---|---|
timeout |
int (10) |
timeout value for the overall interaction. |
dialog |
Dialog |
additional dialog |
command |
str (switchback) |
alternate command. |
In [6]: vdcs = con.list_vdc()
2016-04-04T02:40:35: %UNICON-INFO: +++ None +++
2016-04-04T02:40:35: %UNICON-INFO: +++ execute +++
2016-04-04T02:40:35: %UNICON-INFO: +++ exec show vdc +++
show vdc
Switchwide mode is f2e f3
vdc_id vdc_name state mac type lc
------ -------- ----- ---------- --------- ------
1 step-n7k-2 active 8c:60:4f:75:53:41 Admin None
2 vdc1 active 8c:60:4f:75:53:42 Ethernet f2e f3
3 vdc2 active 8c:60:4f:75:53:43 Ethernet f2e f3
4 vdc3 active 8c:60:4f:75:53:44 Ethernet f2e f3
6 vdc5 active 8c:60:4f:75:53:46 Ethernet f2e f3
step-n7k-2#
In [7]: vdcs
Out[7]: ['step-n7k-2', 'vdc1', 'vdc2', 'vdc3', 'vdc5']
Note
You can call this service even when you are in a VDC. It will switchback,
perform the operation and again come back to the same VDC from where you
executed this API.
switchto¶
switchto is used to switch to any given VDC. This service performs some
basic checks like checking whether the target vdc exists etc. It also makes
sure all the interactions are handled while switching to a VDC for the first
time after creation.
values in parenthesis represent the default value
Argument |
Type |
Description |
|---|---|---|
vdc_name* |
string |
name of the VDC to switch to |
vdc_cred |
str (‘default’) |
Credential to use for first time switching. |
timeout |
int (20) |
timeout value for the overall interaction. |
dialog |
Dialog |
additional dialog |
command |
str (switchto vdc) |
alternate command. |
Most of the time simply providing the VDC name is just good enough.
In [3]: con.switchto('vdc1')
2016-04-04T02:19:28: %UNICON-INFO: +++ switchto vdc +++
2016-04-04T02:19:28: %UNICON-INFO: +++ None +++
2016-04-04T02:19:28: %UNICON-INFO: +++ execute +++
2016-04-04T02:19:28: %UNICON-INFO: +++ exec show vdc +++
show vdc
Switchwide mode is f2e f3
vdc_id vdc_name state mac type lc
------ -------- ----- ---------- --------- ------
1 step-n7k-2 active 8c:60:4f:75:53:41 Admin None
2 vdc1 active 8c:60:4f:75:53:42 Ethernet f2e f3
3 vdc2 active 8c:60:4f:75:53:43 Ethernet f2e f3
4 vdc3 active 8c:60:4f:75:53:44 Ethernet f2e f3
6 vdc5 active 8c:60:4f:75:53:46 Ethernet f2e f3
step-n7k-2#
2016-04-04T02:19:29: %UNICON-INFO: +++ execute +++
2016-04-04T02:19:29: %UNICON-INFO: +++ exec switchto vdc vdc1 +++
switchto vdc vdc1
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (c) 2002-2015, Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under
license. Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or the GNU
Lesser General Public License (LGPL) Version 2.1. A copy of each
such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://www.opensource.org/licenses/lgpl-2.1.php
step-n7k-2-vdc1#
2016-04-04T02:19:31: %UNICON-INFO: +++ execute +++
2016-04-04T02:19:31: %UNICON-INFO: +++ exec term length 0 +++
term length 0
step-n7k-2-vdc1#
2016-04-04T02:19:31: %UNICON-INFO: +++ execute +++
2016-04-04T02:19:31: %UNICON-INFO: +++ exec term width 511 +++
term width 511
step-n7k-2-vdc1#
2016-04-04T02:19:31: %UNICON-INFO: +++ execute +++
2016-04-04T02:19:31: %UNICON-INFO: +++ exec terminal session-timeout 0 +++
terminal session-timeout 0
step-n7k-2-vdc1#
2016-04-04T02:19:31: %UNICON-INFO: +++ config +++
config term
Enter configuration commands, one per line. End with CNTL/Z.
step-n7k-2-vdc1(config)# no logging console
step-n7k-2-vdc1(config)# line console
step-n7k-2-vdc1(config-console)# exec-timeout 0
step-n7k-2-vdc1(config-console)# terminal width 511
step-n7k-2-vdc1(config-console)# end
step-n7k-2-vdc1# Out[3]: 'vdc1'
You see a relatively longer output because every time it switches to a new VDC, the terminal is reinitialized.
Note
You don’t need to switchback to execute this API. You can call switchto
even when you are already inside a VDC. switchback is implicitly called.
switchback¶
It is just the opposite of switchto. It is used to return to the default
VDC. This service takes no mandatory arguments.
Argument |
Type |
Description |
|---|---|---|
timeout |
int (10) |
timeout value for the overall interaction. |
dialog |
Dialog |
additional dialog |
command |
str (switchback) |
alternate command. |
In [4]: con.switchback()
2016-04-04T02:34:51: %UNICON-INFO: +++ switchback +++
2016-04-04T02:34:51: %UNICON-INFO: +++ execute +++
2016-04-04T02:34:51: %UNICON-INFO: +++ exec switchback +++
switchback
step-n7k-2#
Note
If you call this API while being in a default VDC, then the
call will be simply bypassed.
create_vdc¶
This service creates a VDC by name.
Argument |
Type |
Description |
|---|---|---|
vdc_name* |
string |
name of the VDC to create. |
timeout |
int (120) |
timeout value for the overall interaction. |
dialog |
Dialog |
additional dialog |
command |
str (vdc) |
alternate command. |
In [10]: con.create_vdc('vdc1')
2016-04-04T02:49:49: %UNICON-INFO: +++ create vdc +++
2016-04-04T02:49:49: %UNICON-INFO: +++ None +++
2016-04-04T02:49:49: %UNICON-INFO: +++ execute +++
2016-04-04T02:49:49: %UNICON-INFO: +++ exec show vdc +++
show vdc
Switchwide mode is f2e f3
vdc_id vdc_name state mac type lc
------ -------- ----- ---------- --------- ------
1 step-n7k-2 active 8c:60:4f:75:53:41 Admin None
3 vdc2 active 8c:60:4f:75:53:43 Ethernet f2e f3
4 vdc3 active 8c:60:4f:75:53:44 Ethernet f2e f3
6 vdc5 active 8c:60:4f:75:53:46 Ethernet f2e f3
step-n7k-2#
2016-04-04T02:49:50: %UNICON-INFO: +++ config +++
config term
Enter configuration commands, one per line. End with CNTL/Z.
step-n7k-2(config)# vdc vdc1
Note: Creating VDC, one moment please ...
2016 Apr 3 14:52:30 %$ VDC-2 %$ %SYSLOG-2-SYSTEM_MSG : logflash ONLINE
step-n7k-2(config-vdc)# end
step-n7k-2# Out[10]: 'vdc1'
Note
You can call this API from any VDC. It will create the VDC and again come back to the same VDC from which it was called.
delete_vdc¶
This service can be used for deleting a vdc.
Argument |
Type |
Description |
|---|---|---|
vdc_name* |
string |
name of the VDC to delete |
timeout |
int (90) |
timeout value for the overall interaction. |
dialog |
Dialog |
additional dialog |
command |
str (no vdc) |
alternate command. |
In [9]: con.delete_vdc('vdc1')
2016-04-04T02:45:04: %UNICON-INFO: +++ delete vdc +++
2016-04-04T02:45:04: %UNICON-INFO: +++ None +++
2016-04-04T02:45:04: %UNICON-INFO: +++ execute +++
2016-04-04T02:45:04: %UNICON-INFO: +++ exec show vdc +++
show vdc
Switchwide mode is f2e f3
vdc_id vdc_name state mac type lc
------ -------- ----- ---------- --------- ------
1 step-n7k-2 active 8c:60:4f:75:53:41 Admin None
2 vdc1 active 8c:60:4f:75:53:42 Ethernet f2e f3
3 vdc2 active 8c:60:4f:75:53:43 Ethernet f2e f3
4 vdc3 active 8c:60:4f:75:53:44 Ethernet f2e f3
6 vdc5 active 8c:60:4f:75:53:46 Ethernet f2e f3
step-n7k-2#
2016-04-04T02:45:05: %UNICON-INFO: +++ config +++
config term
Enter configuration commands, one per line. End with CNTL/Z.
step-n7k-2(config)# no vdc vdc1
Deleting this vdc will remove its config. Continue deleting this vdc (y/n)? [no] yes
Note: Deleting VDC, Files under bootflash:/vdc_2/* will be deleted! One moment please ...
step-n7k-2(config)# end
step-n7k-2# Out[9]: 'vdc1'
Note
You can call delete_vdc even when you are inside a VDC. Only thing to
take care is that you can’t delete the same VDC in which you are already
in. Isn’t is obvious !!
reload¶
Service to reload the device.
Sometimes reload fails because device prompt is unable to match
due to console messages over terminal and this results in reload timeout.
In such a case prompt_recovery can be used to recover the device.
Argument |
Type |
Description |
|---|---|---|
reload_command |
str |
reload command to be issued on device. default reload_command is “reload” |
dialog |
Dialog |
additional dialogs/new dialogs which are not handled by default. |
timeout |
int |
timeout value in sec, single-rp/dual-rp Default is 400/700 sec |
prompt_recovery |
bool (default False) |
Enable/Disable prompt recovery feature |
return_output |
bool (default False) |
Return namedtuple with result and reload command output |
config_lock_retries |
int (default 20) |
retry times if config mode is locked |
config_lock_retry_sleep |
int (default 9 sec) |
sleep between config_lock_retries |
image_to_boot |
str |
n9k plugin only: boot from specified image if device goes into loader state |
reload_creds |
list or str (‘default’) |
Credentials to use if device prompts for user/pw. |
reconnect_sleep |
int (default 60 sec) |
sleep time interval before reconnect device |
- return :
True on Success
raise SubCommandFailure on failure.
If return_output is True, return a namedtuple with result and reload command output
#Example
--------
rtr.reload()
# If reload command is other than 'reload'
rtr.reload(reload_command="reload location all", timeout=400)
# using prompt_recovery option
rtr.reload(prompt_recovery=True)
# using return_output
result, output = rtr.reload(return_output=True)